John Deere 44SB Snowblower Maintenance, Parts & Repair

john deere

John Deere 44SB Snowblower Maintenance, Parts and Repair Guide

The John Deere 44SB is a front-mounted, two-stage snowblower attachment driven by the tractor’s power take-off (PTO) through a belt drive. It has no engine of its own. This guide covers gearbox oil checks, belt and shear-bolt inspection, parts identification, and repairs for a stopped auger, rapid belt wear, or uneven clearing. Deere publishes separate manuals for different 44-inch attachment and tractor combinations, so match the instructions to your attachment before servicing it or buying parts.manuals.deere+3

44SB Snowblower Maintenance

Park on level ground, disengage the PTO, lower the blower fully to the ground, set the parking brake, shut off the tractor, and remove the key. Wait for the auger, impeller, and belt drive to stop. Before cleaning, inspecting, or repairing the attachment, follow Deere’s accidental-start precautions: disconnect the tractor spark-plug wire or battery as directed by the applicable manuals. Never work beneath an attachment held up only by its lift. For a blockage, shut down the tractor, wait for all movement to stop, and use a cleanout tool—not your hands—to clear the chute or housing.manuals.deere+2

Maintenance schedule and service points

The scheduled checks below come from Deere’s Select Series manual OMM170956 for the configuration it covers. If your attachment uses a different manual, use that manual’s schedule. The last two rows are inspection triggers, not recurring service intervals.manuals.deere+1

Maintenance task Verified interval or trigger Specification or inspection point Owner action
Check shear bolts Each use under OMM170956 Auger and impeller shear hardware Look for missing or broken bolts. Identify and correct the cause before fitting the specified replacement. manuals.deere+1
Check chute rotation Each use under OMM170956 Chute should rotate freely Check for ice or obstruction with the machine isolated. Lubricate if required by the applicable instructions. manuals.deere+1
Inspect the drive belt Beginning of the season under OMM170956 Excessive wear Check for fraying, damaged edges, or other visible deterioration. If wear is concentrated on one edge, check the guides and idlers before fitting a new belt. manuals.deere+1
Check both gearbox oil levels Beginning of the season and before installation under OMM170956 Auger gearbox and snowblower drive gearbox Check both with the blower removed, using the plug locations and level procedure in the applicable manual. manuals.deere+2
Inspect the scraper blade and skid shoes When clearing becomes uneven or wear is visible Lower cutting edge and the shoes that set its clearance Look for uneven shoe settings, wear, and a bent or damaged scraper. manuals.deere+1
Inspect after an impact or sudden vibration Before restarting Auger, impeller, housing, shear hardware, and guards Stop and isolate the machine. Repair impact damage or have the cause of vibration diagnosed before operating again. manuals.deere+1

Lubrication and fluid requirements

On the Select Series configuration covered by OMM170956, the auger gearbox and the snowblower drive gearbox are separate units. Both have removable plugs for checking and topping up oil, but Deere describes their internal components as non-serviceable. Check both boxes with the blower removed. Use the oil specification and level in the manual that matches your unit rather than assuming that every 44-inch attachment uses the same procedure.manuals.deere+1

For attachments covered by OMUC13236, Deere specifies 80W-90 GL-5 gear oil for both gearboxes. With the blower removed and the gearbox approximately level, the oil should reach the bottom of each check-plug hole. Add oil only as needed. If the oil level falls again or fresh oil appears around a shaft or housing, have the source of the leak identified rather than relying on repeated top-ups.manuals.deere

OMM170956 lists Deere Multi-Purpose SD Polyurea Grease and Multi-Purpose HD Lithium Complex Grease as preferred products, with a general-purpose NLGI No. 2 grease as an alternative under the conditions described in that manual. That specification applies where the manual calls for grease; it is not an instruction to grease every bearing or put grease in either gearbox.manuals.deere+1

Wear checks that can reveal repair needs

  • Scraper blade and skid shoes: A rounded or bent scraper, a shoe worn more heavily on one side, or unequal shoe settings can leave a strip of snow. Compare both sides before changing the tractor’s lift adjustment.manuals.deere

  • Belt, guides, and idlers: A frayed edge or fresh rub mark is a reason to check the belt path. Deere identifies belt-guide adjustment and idler alignment as checks when belts wear too fast or break.manuals.deere+1

  • Auger, impeller, and housing: After an impact, look for bent metal, fresh contact marks, or broken shear hardware. Do not restart a blower with visible damage to a rotating part or evidence it has rubbed the housing.manuals.deere+1

  • Guards and fasteners: Correct missing or loose hardware and reinstall any shields removed for service before operating. Use the parts diagram to distinguish ordinary mounting fasteners from shear hardware.manuals.deere+2

Preseason preparation and storage

Before mounting the blower, finish the belt and gearbox checks that are easier to do with the attachment off the tractor. Confirm that the chute moves freely and that you have the correct shear hardware for both the auger and impeller. Deere also advises running the blower for a few minutes after clearing snow, from the operator’s seat and in a safe area, to help prevent the collector or impeller from freezing.manuals.deere+3

For seasonal storage, Deere’s Select Series instructions call for removing and cleaning the attachment, repairing damaged parts, tightening loose hardware, and touching up exposed painted surfaces. The instructions also call for a thin coat of grease on blades and engine oil on pivots where applicable. Store the attachment on a non-abrasive surface or wooden blocks; if stored outdoors, protect it with a waterproof cover. Follow the tractor manual separately for fuel and battery storage.manuals.deere+2

Finding the Correct 44SB Replacement Parts

A worn belt or broken shear bolt tells you what to inspect next, but not necessarily what to order. Deere’s manuals distinguish between different 44-inch applications, and the tractor-side mounting and drive parts may be listed separately from the blower housing and its rotating assemblies.manuals.deere+4

Model, serial number, and configuration checks

Record the complete product identification number (PIN) from the blower’s identification label, including its letters and leading zeros. Also record the tractor model and PIN. If the attachment was bought used, note which mounting brackets, lift parts, and drive components came with it; the tractor it came off is not proof that all of those parts fit yours.manuals.deere+3

Do not order by “44SB” or by width alone. Use the attachment PIN to select the correct catalog entry and any serial range printed against the assembly or part. Use the tractor details as well when identifying compatibility-kit, lift, or tractor-side drive parts. There is no single serial cutoff in this guide that applies to every 44SB configuration.manuals.deere+4

Parts diagrams and manuals

Use the John Deere Parts Catalog to find the illustrated breakdown, and the John Deere Technical Information Store or an authorized dealer to identify the operator’s manual and installation instructions. OMM170956 covers specified Select Series attachments; OMUC13236 covers listed D-, E-, and S-series tractor applications; and OMM175856 covers another group of Select Series tractors. These publication numbers are starting points, not substitutes for a PIN match.manuals.deere+4

A number beside an illustration is a callout: it points to a row in the parts list. Order using the part number in that row, after checking any serial qualification. If Deere lists a superseding number, confirm that it replaces the original for your application and whether it is an individual part or an assembly. For a gearbox, check what the assembly includes before assuming that mounting hardware or other external parts come with it.manuals.deere+2

Replacement parts and fitment checks

The numbers below are listed in OMM170956 for its 44-inch Select Series configuration. They are not a universal 44SB parts list. Confirm the current orderable number against the attachment PIN.manuals.deere+1

Component Deere part number Fitment qualification What to check before ordering
Snowblower drive belt M149970 44-inch configuration covered by OMM170956 Match the belt to the snowblower drive illustration, not the tractor’s mower-deck belt listing. manuals.deere+2
Auger shear bolt and nut 19M7834 bolt; 14M7397 nut Same configuration; one bolt at each auger shaft Select the auger callout, not the impeller callout. manuals.deere+1
Impeller shear bolt and locknut 19M8321 bolt; 14M7397 locknut Same configuration; two bolts at the impeller Verify the impeller listing for the 44-inch version, not the 47-inch version in the same manual. manuals.deere+1
Scraper blade M155105 44-inch configuration covered by OMM170956 Select the blade across the bottom of the housing and check whether its fasteners are separate. manuals.deere+1

Shear bolts: auger and impeller are different

A shear bolt is designed to break under overload so the drive is less likely to be damaged. In the 44-inch OMM170956 configuration, both the auger and impeller bolts are listed as M6 × 45, but they have different part numbers. The dimensions alone do not identify the correct replacement. Do not substitute an ordinary bolt, fit a harder bolt, or move a bolt from one application to the other based on size. Deere directs owners to find and correct the reason the bolt sheared before installing the replacement.manuals.deere+1

Parts sources in the USA and Canada

In both countries, start with the John Deere Parts Catalog and an authorized John Deere dealer’s parts department. Give the dealer the attachment PIN, tractor model and PIN if the part is on the tractor side, and the diagram callout or original part number. Ask the dealer to confirm the current number and what is included. If comparing a domestic quote with a cross-border order, compare totals in the same currency after shipping, taxes, and any applicable import charges.manuals.deere+3

44SB Snowblower Problems and Repairs

Deere’s Select Series troubleshooting chart gives specific starting points for a stopped auger or impeller, rapid belt wear, and uneven clearing. Those are inspection leads, not diagnoses. A chute that binds and an attachment that vibrates after an impact require different checks; neither symptom, on its own, establishes a failed gearbox.manuals.deere+2

Troubleshooting at a glance

Symptom Plausible causes or documented checks First safe check Repair direction or escalation
Auger or impeller does not turn Broken shear bolt; worn or broken drive belt Isolate the tractor and inspect the relevant shear hardware and visible belt condition. Replace only the confirmed failed part. If both checks are inconclusive, have the drive inspected. manuals.deere+1
Belt frays quickly or breaks again Guide contact or idler misalignment With the drive stopped and isolated, look for edge wear and matching rub marks. Correct the routing, guide setting, or idler fault before installing another belt. manuals.deere+1
Blower leaves more snow on one side Uneven skid shoes; scraper damage; on applicable setups, lift-assist adjustment Lower onto a level surface and compare both shoes and the scraper edge. Correct the confirmed wear or setting before changing the lift linkage. manuals.deere+1
Chute is hard to turn Ice or debris; lubrication needed; possible binding in the rotation mechanism Shut down and check for visible obstruction without reaching into the discharge opening. Clear safely and follow the manual’s lubrication instructions. Inspect the rotation mechanism if binding remains. manuals.deere+2
Sudden vibration after an impact Possible bent rotating part, housing contact, or other impact damage Stop immediately and inspect for damage after isolation. Do not run a damaged or unexplained vibrating attachment to see whether it clears itself. manuals.deere+1

The auger or impeller stops turning

If only one side of the auger appears to have stopped feeding snow, start with the shear bolt for that side. If the impeller stopped throwing snow, inspect its separate shear hardware as well. If neither stage appears to receive drive, inspect the belt. Deere lists both belt failure and broken shear bolts for this symptom; a stopped auger alone does not establish which part failed. Make these inspections with the tractor isolated, not by approaching the running attachment.manuals.deere+2

If a bolt is broken and the attachment is otherwise undamaged, clear the cause of the overload and follow the applicable manual’s alignment and replacement instructions. If the holes will not align as described, the rotating parts are visibly damaged, or the replacement bolt shears again without an obvious obstruction, stop. Have the shaft, housing clearances, and drive inspected rather than fitting a stronger bolt.manuals.deere+1

The belt wears through an edge or breaks repeatedly

Deere directs owners to check the belt guides and idler alignment when a belt wears too quickly or breaks. A damaged edge together with a bright rub mark on a guide provides a more useful clue than belt damage alone. Compare the routing with the applicable diagram; an idler is a pulley that guides or tensions the belt. OMM170956 specifies that the guides must not touch the belt after installation.manuals.deere+1

If inspection confirms a routing or guide-setting error, correct it using the manual that matches the machine before replacing the belt. The documented Select Series replacement procedure requires mechanically supporting the raised attachment for part of the job. If you cannot support it as specified, safely release belt tension, or determine why an idler is out of line, have the work done by a dealer.manuals.deere+1

The blower leaves a strip or clears unevenly

Compare the skid shoes before adjusting the lift. They set the height of the scraper relative to the surface, so unequal settings or wear can leave a deeper strip on one side. A bent scraper can produce an uneven edge even when the shoes are set alike. If the shoes are sound, set them using the applicable procedure for the surface you clear. If the scraper is damaged, inspect its mounting edge before fitting the correct replacement.manuals.deere+1

For the 44-inch Select Series setup documented in OMM170956, Deere also lists lift-assist spring adjustment for uneven clearing. Treat that as a separate check after the scraper and shoes. If the housing is twisted or the linkage binds, have the mounting and lift system inspected rather than trying to compensate with a shoe adjustment.manuals.deere+2

The discharge chute binds or will not turn

Deere calls for a free-rotation check at each use under OMM170956. If the chute binds after wet snow or storage, inspect for ice or packed debris with the machine safely shut down. Use a cleanout tool where there is a blockage; never reach through the chute. If the obstruction clears, check chute movement again with the tractor still isolated and lubricate only as specified for your configuration.manuals.deere+2

If the chute still binds when clear, inspect the visible rotation handle, bracket, and chute mounting area for loose hardware or visible damage. These are inspection points, not evidence of a known defect. Use the diagram for the fitted rotation assembly to identify what is damaged before ordering a part.manuals.deere+2

The blower vibrates after striking an object

Stop immediately. Once the attachment is lowered and the tractor is isolated, look for bent auger flighting—the spiral metal that feeds snow inward—fresh scrape marks in the housing, and damaged shear hardware. A broken bolt may be only one result of the impact. Its replacement does not make a bent auger or contacting impeller safe to run.manuals.deere+2

If you find housing contact, a damaged impeller, or obvious shaft movement, leave the blower out of service for inspection. Do the same if the cause of the vibration is not visible. Straightening a rotating part by eye is not a substitute for checking its condition and clearance.manuals.deere+1

Owner Maintenance or Professional Repair?

Owner work is most straightforward when the fault is visible and the matching manual covers the procedure: checking gearbox oil, replacing a correctly identified shear bolt after clearing the cause, or servicing a worn scraper or skid shoe. A belt replacement is also documented for the Select Series configuration, but it depends on safely supporting the attachment and following the specified routing and guide settings.manuals.deere+4

Use professional service for unexplained vibration, damaged rotating assemblies, a distorted housing or mount, a lift mechanism that will not hold securely, or a gearbox that repeatedly loses oil. On the Select Series configuration covered by OMM170956, checking gearbox oil is owner maintenance; internal gearbox repair is not a documented owner procedure. If a major assembly is damaged, get a confirmed repair scope, parts availability, and a local labor quote before comparing the repair cost with the condition and value of the complete attachment.manuals.deere+2

Frequently Asked Questions

Can I use a 47-inch Select Series manual for my 44SB?

Some Deere publications cover both widths. Use the instructions, illustrations, and parts entries specifically marked for the 44-inch version, and confirm the publication applies to your attachment. In OMM170956, for example, the 44-inch and 47-inch impeller shear hardware is different.manuals.deere+2

Does a used 44-inch blower come with everything needed to mount it?

Not necessarily. Deere’s instructions distinguish the blower assembly from items such as the front lift assembly and, on certain tractors, a compatibility kit. Compare the included hardware with the installation instructions for the exact tractor and attachment before trying to mount it.manuals.deere+2

Should I drain and refill the gearboxes every season?

OMM170956 lists a beginning-of-season oil-level check, not an annual drain-and-refill procedure. Check each gearbox using the instructions for your attachment, top up only as directed, and investigate a recurring drop in level.manuals.deere+1