John Deere 59-Inch Snowblower Maintenance, Parts and Repair Guide
John Deere 59-inch snowblower maintenance starts with the two gearboxes, PTO driveline, auger shaft and discharge chute. This guide explains how to service those points, identify replacement parts and narrow down faults such as a stopped auger, a chute that moves only one way or a gearbox that keeps leaking. Deere published different manuals for 59-inch attachments, and even the correct oil level at the snowblower gearbox check hole differs between versions.manuals.deere+1
59-Inch Snowblower Maintenance
Park the tractor on level ground, disengage the power take-off (PTO), lower the snowblower to the ground, stop the engine, set the parking brake and remove the key. Wait for the auger and impeller to stop before working on the attachment. Never work beneath a snowblower held up only by the tractor hydraulics; where the manual calls for raising it to service the scraper or skid shoes, use the specified blocking procedure. Clear a blockage with a clean-out tool, never your hands, and stay out of the auger and impeller openings. If the job involves opening a hydraulic connection, follow the tractor manual’s pressure-relief procedure first.manuals.deere+3
Maintenance Schedule and Service Points
The schedule below applies to the front-mounted 59-inch snowblower covered by operator’s manual OMLVU17390. The attachment is PTO-driven; tractor hydraulics raise and lower it and operate the discharge chute on this configuration. Tractor engine maintenance belongs to the tractor’s own service schedule.manuals.deere+2
| Maintenance task | Verified interval or trigger | Specification or inspection point | Owner action |
|---|---|---|---|
| Lubricate the discharge chute | Before each use | Contact surface beneath the rotating chute | Apply the recommended grease under the chute. manuals.deere |
| Check the auger gearbox oil and vent | Every 25 hours | Oil level at the check hole; cross-hole vent in the fill plug | Check the oil level and make sure the vent is clear. manuals.deere |
| Check the snowblower gearbox oil | Every 25 hours | Check plug on the separate snowblower gearbox | On the OMLVU17390 configuration, check that the oil is level with the check hole. manuals.deere |
| Lubricate the gearbox driveshaft, PTO driveshaft and auger shaft | Every 25 hours | Gearbox driveshaft fitting, universal-joint fittings, sliding inner shaft and auger fittings | Grease each point as directed; the application amount differs by location. manuals.deere |
| Inspect the auger shear bolts | After striking a solid object or losing auger drive | One shear bolt at each end of the auger shaft | Stop immediately after an impact. Find and correct the cause before fitting a replacement. manuals.deere |
| Inspect the scraper blade and skid shoes | Condition-based; inspect if clearance becomes uneven or the housing starts contacting the surface | Scraper edges, shoe wear and matching shoe positions | Reverse the scraper if one edge remains serviceable; replace it if both edges are worn, rough or bent. Replace damaged shoes and set both to the same position. manuals.deere+1 |
Lubrication and Fluid Requirements
The auger gearbox and the snowblower gearbox are separate oil checks. Locate both plugs using the service illustrations for your attachment before removing either one. Deere’s OMLVU17390 manual recommends GL-5 gear lubricant, with viscosity selected for the expected air temperature. Use the specified level rather than guessing a fill quantity.manuals.deere
-
Auger gearbox: With the attachment level, remove the check plug. Oil should reach the check hole. If it is low, add the specified lubricant through the fill opening. Check the cross-hole vent in the fill plug while servicing the gearbox; a blocked vent can build pressure and cause leakage.manuals.deere
-
Snowblower gearbox: On the configuration covered by OMLVU17390, oil should reach the check hole. Do not transfer that level to the 59-inch attachment covered by OMM137705, identified in that manual as serial number 070001 and up for 4200, 4300, 4400 and 790 compact utility tractors. For that configuration, Deere specifies checking with a bent wire for a level 19 mm (3/4 in.) below the check hole and recommends 80W-90 GL-5 gear lubricant.manuals.deere+1
For the OMLVU17390 configuration, Deere prefers Multi-Purpose SD Polyurea Grease or Multi-Purpose HD Lithium Complex Grease and allows a general-purpose NLGI No. 2 grease when the preferred products are not used. Apply one or two shots to the gearbox driveshaft fitting and each universal-joint fitting. Grease the sliding inner shaft and extend and compress it several times to distribute the grease. At the auger fittings, apply grease until it just appears at the shaft ends near the gearbox. Grease under the chute before use and apply only a light coating to the cable pulleys. Do not overgrease the gearbox driveshaft fitting; Deere warns that this can damage the seal.manuals.deere
Wear Checks That Can Reveal Repair Needs
Use a routine service stop to inspect the parts that determine how the blower sits, turns and transfers power. The following visual checks help identify the next step; they are not a substitute for the manual’s repair procedures.manuals.deere+2
-
Scraper and skid shoes: Look for a rounded or bent scraper edge, a shoe worn through at the contact surface or different mounting heights from side to side. Check the shoes before ordering a scraper; uneven clearance can come from the setup rather than the blade.
-
Auger and impeller: Look for bent flighting—the spiral blades on the auger—fresh rub marks, cracks or contact with the housing. If a rotating part appears bent or loose, do not run the blower to see whether it clears.
-
Driveline, hitch and guards: Check for missing retaining hardware, a visibly damaged shield or obvious looseness at a coupling. Restore the correct hardware and guarding before operating; have a damaged joint or loose shaft assessed rather than trying to quiet it with grease.
-
Chute controls: Look for frayed cable strands, a cable out of its pulley groove or oil around the hydraulic cylinder and hose connections. A cable problem and a hydraulic problem require different repairs. Never use your hand to check for a pressurized hydraulic leak.
-
Gearboxes: Look for fresh oil at the vent, plugs, housing joints and shaft exits. Note where it first appears before cleaning. That observation is more useful than oil spread over the housing after operation.manuals.deere+3
Preseason Preparation and Storage
Before the first snowfall, check both gearbox levels, clear the auger gearbox vent, service the grease points and inspect the scraper, skid shoes, guards and chute cable. Verify that you have the correct spare auger shear hardware. On the OMLVU17390 configuration, Deere shows the kickstand in its vertical position for removal and folded to its operating position before use. Follow the matched removal instructions rather than relying on the stand to support an attachment that has not been set down properly.manuals.deere+2
At the end of the season, remove packed snow and debris, let the attachment dry and inspect exposed metal and wear surfaces before putting it away. Keep the detached blower stable with the supports specified for its configuration. If an inspection turns up a worn scraper, damaged cable or failed coupling, identify the exact assembly before ordering; the 59-inch designation alone does not establish fit.manuals.deere+2
Finding the Correct 59-Inch Snowblower Replacement Parts
Model, Serial Number and Configuration Checks
Record the complete product identification or serial number from the snowblower itself. Photograph the tag and the assembly you are repairing. Also record the tractor model and, if known, the hitch or mounting kit. Those details help distinguish attachment parts from the front hitch, connecting driveline and tractor-side hydraulic or PTO components.manuals.deere+3
Deere’s OMM137705 identifies a 59-inch configuration for 4200, 4300, 4400 and 790 compact utility tractors at attachment serial number 070001 and up. Deere also published a standalone North American 59-inch manual, OMLVU17390, and a separate manual covering 47-, 54-, 59- and 60-inch snowblowers. Do not treat the serial range printed in one manual as a universal break for every John Deere 59-inch blower. If the tag is unreadable, ask a dealer to help identify the attachment from the tractor and hitch details and photographs of the gearboxes, driveline and chute mechanism before ordering.manuals.deere+3
Parts Diagrams and Manuals
Use the John Deere Parts Catalog to find the illustrated assembly for the identified attachment. Match the drawing to the machine and read any serial-number or configuration notes beside the listing. Use the operator’s manual for owner-service procedures; a parts drawing shows how pieces are grouped, but it does not establish an adjustment, torque or safe disassembly procedure. The John Deere Technical Information Store or an authorized dealer can help identify the applicable operator’s manual and service literature.manuals.deere+2
The number beside an arrow in a diagram is a reference number, not necessarily the number you order. Read across to the orderable part number and confirm whether it buys one component, a hardware kit or a complete assembly. If a number has been superseded, have the dealer confirm the current replacement against your attachment’s serial number and check whether the replacement needs any additional hardware.partscatalog.deere
Replacement Parts and Fitment Checks
| Component | Part-number lookup | Fitment qualification | What to check before ordering |
|---|---|---|---|
| Auger shear bolt and retaining hardware | Auger shaft or coupling illustration | Match the shear location at the end of the auger shaft on the identified attachment. | Confirm the specified bolt and its retaining hardware; do not order by diameter alone. manuals.deere+2 |
| Scraper blade | Housing or scraper illustration | Match the reversible blade to the housing. | Compare the mounting-hole pattern and check whether bolts and nuts are listed separately. manuals.deere+2 |
| Skid shoes | Housing and skid shoe illustration | Match the shoe and mounting arrangement shown for your attachment. | Compare the bracket, adjustment holes and hardware with the installed parts. manuals.deere+2 |
| Discharge chute cable assembly | Chute rotation or hydraulic cylinder linkage illustration | On the documented cable-and-cylinder design, the assembly has unequal cable ends. | Match the cable ends, anchor and pulley layout. Identify a damaged pulley separately rather than assuming it comes with the cable. manuals.deere+2 |
| Gearbox plug, seal or assembly | Auger gearbox or snowblower gearbox illustration | The two gearboxes have different locations and service points. | Identify which gearbox is leaking and whether the failed item is listed separately. Distinguish the vented fill plug from the oil-level check plug. manuals.deere+2 |
| Driveshaft or joint | Attachment or hitch driveline illustration, as applicable | Match the shaft’s position between the tractor, hitch and blower. | Verify which shaft needs work and whether the joint, shield or complete shaft is the orderable item. manuals.deere+2 |
Shear Bolts and Critical Hardware
Deere documents a shear bolt at each end of the auger shaft on the configurations described above. These bolts are intended to break when the auger strikes a solid object, protecting the drive from more serious damage. Correct the cause of the failure and install the specified shear hardware. Do not substitute an ordinary bolt, choose a harder grade or assume the auger bolt applies at another point in the driveline. On the OMM137705 configuration, Deere also instructs owners to align the two couplings in the same position when installing a replacement.manuals.deere+1
Parts Sources in the USA and Canada
In both the United States and Canada, start with the John Deere Parts Catalog, then use an authorized John Deere dealer to confirm fitment or a superseded number. Give the parts counter the attachment serial number, the tractor and hitch details if the part is on the driveline, and the diagram reference or candidate part number. If comparing quotes across the border, confirm the currency, shipping, taxes and any import charges before comparing delivered cost.partscatalog.deere
59-Inch Snowblower Problems and Repairs
Start by locating the fault: at an individual auger section, in the tractor-to-attachment drive, in the chute linkage or at a gearbox. Deere documents the service procedures for these assemblies, but the symptom alone does not identify the failed part. Perform the first checks with the attachment lowered and the tractor shut down as described above.manuals.deere+3
Troubleshooting at a Glance
| Symptom | Plausible causes | First safe check | Repair direction or escalation |
|---|---|---|---|
| One auger section stops feeding after an impact | Sheared bolt, obstruction or impact damage | Inspect the bolt at the affected auger end and look for trapped material or fresh rub marks. | Clear the obstruction and fit the specified bolt only if the auger, coupling and housing are sound. manuals.deere+1 |
| Neither the auger nor the impeller receives drive | Disconnected driveline, damaged joint or fault farther upstream | Check the accessible driveline connections against the installation instructions. | Correct a verified connection problem; seek service if the installed drive is intact but still does not transmit power. manuals.deere+2 |
| Chute stalls or moves only one way | Ice or debris, damaged cable or pulley, or a hydraulic fault | Inspect the chute base, visible cable routing and cylinder area. | Correct a confirmed mechanical fault; escalate an unexplained cylinder or hydraulic fault. manuals.deere+2 |
| Scraper leaves an uneven strip | Unequal skid shoe positions, worn scraper edge or damage from an impact | On level ground, compare both shoes and inspect the full scraper edge. | Match the shoe positions, reverse or replace the scraper as appropriate, or have a distorted housing assessed. manuals.deere+1 |
| Oil reappears around a gearbox | Blocked auger gearbox vent, leakage at a plug or possible seal or housing damage | Locate the wet area, check the oil level by the matched procedure and inspect the auger gearbox vent if applicable. | Clear a confirmed vent obstruction; seek service for a recurring leak, shaft movement or a cracked housing. manuals.deere+1 |
One Auger Section Stops or Keeps Breaking Shear Bolts
A section that stops feeding snow just after the blower strikes a solid object is consistent with the protective action Deere describes. Inspect the shear bolt at the affected end. If it has failed, check for the object that caused the impact and look for bent flighting, fresh housing contact or damaged bolt holes before installing another bolt.manuals.deere+1
If the obstruction is gone and the shaft, coupling and housing appear undamaged, follow the matched manual’s replacement procedure. If the correct bolt breaks again without another obvious impact, stop replacing bolts and have the coupling, shaft and auger alignment checked. A new shear bolt restores the connection; it does not correct a part that binds.manuals.deere+1
The Auger and Impeller Both Stop
When neither stage receives drive, start with the parts they share rather than assuming both auger shear bolts failed. If the fault began after mounting the blower, compare the visible PTO shaft connections and hitch installation with the applicable instructions. Look for a coupling that is not fully seated, missing retention hardware or visible driveline damage. Never run the blower with a guard removed to watch where rotation stops.manuals.deere+2
If a coupling is simply not seated and no parts are damaged, reconnect it using the installation procedure and verify that it locks as specified before operating. If the driveline is correctly installed but still does not transmit power, have the tractor PTO, shafts and gearbox input checked. A stationary auger and impeller do not, by themselves, justify replacing a gearbox.manuals.deere+3
The Discharge Chute Stalls or Turns Only One Way
On the OMLVU17390 configuration, a hydraulic cylinder turns the chute through a cable-and-pulley assembly. That matters because the cylinder can operate yet fail to turn the chute properly if a cable is damaged, displaced or incorrectly routed. With the tractor shut down, inspect the chute base for ice or debris and look for a frayed cable, a cable outside its pulley groove or a damaged pulley.manuals.deere+1
If the cable assembly is damaged, use the manual’s cylinder-positioning, cable-routing and shield-installation instructions. The two cable ends are unequal and route differently. Do not pull a loaded cable free or open a hydraulic line to see whether it has pressure. If the linkage is intact and free but the cylinder does not respond, or if you find oil at a hose or cylinder connection, have the hydraulic side diagnosed.manuals.deere+3
The Scraper Leaves an Uneven Strip
Check the skid shoes on a flat surface before condemning the scraper. Deere specifies that both shoes occupy the same position on the OMLVU17390 configuration. The mounting holes change scraper height in 13 mm (1/2 in.) increments. If the shoes are correctly matched but the cutting edge is uneven, inspect the full width of the scraper and the mounting lip behind it.manuals.deere+1
Deere provides a procedure for reversing the scraper when one edge is worn, rough or bent, and replacing it when both edges are damaged. Use the manual’s blocking procedure before removing the blade or shoes. If the housing lip or shoe mount is bent, cracked or has elongated mounting holes, assess the housing before spending money on a blade that may not sit straight.manuals.deere+1
Gearbox Oil Keeps Reappearing
First determine which gearbox is wet and where the oil starts. Deere specifically warns that a blocked cross-hole vent in the auger gearbox fill plug can cause pressure buildup and leakage. Check the vent and verify the oil level using the procedure for that gearbox and attachment. The check-hole level for one configuration can be wrong for another.manuals.deere+1
If the vent was obstructed, clear it as directed, clean the outside of the gearbox and check whether fresh oil returns. If oil reappears at a shaft exit, the level keeps falling or the shaft has noticeable play, stop operating the blower and have the seal, shaft support and housing assessed. Topping up the gearbox does not correct an ongoing loss of oil.manuals.deere+2
Owner Maintenance or Professional Repair?
With the correct manual and safe support, an owner can grease the specified points, check the two gearbox levels, clean the auger gearbox vent, replace a confirmed broken shear bolt and service the scraper or skid shoes. Chute cable replacement is also documented, but it requires correct cylinder positioning, routing, tensioning and reinstallation of the shield. If those steps cannot be carried out safely, have the cable fitted by a dealer.manuals.deere+1
Leave persistent vibration, bent rotating parts, shaft or bearing play, internal gearbox faults and unresolved hydraulic problems to a technician. If the repair is more extensive than replacing a wear part, ask for an assessment of the housing, auger, impeller and driveline before deciding whether to proceed. Compare the confirmed parts and labor quote with the condition and value of the complete attachment, not just the price of the first part that appears damaged.manuals.deere+2
Frequently Asked Questions
Can I fill both gearboxes to the bottom of their check holes?
Only if the service instructions for your attachment specify that level for both. OMLVU17390 specifies oil at both check holes. OMM137705 specifies oil at the auger gearbox check hole but 19 mm (3/4 in.) below the snowblower gearbox check hole. Match the manual before adding oil.manuals.deere+1
Can I order a driveshaft using only the tractor model?
Do not use the tractor model alone. Identify the tractor, hitch and blower, then establish whether the shaft in question is on the tractor-to-hitch side or the attachment side. The illustrated parts catalog and installation drawings help distinguish the shafts and their guards.manuals.deere+2
Does hydraulic chute rotation mean the auger is hydraulically driven?
No. On the OMLVU17390 configuration, tractor hydraulics move the chute and raise or lower the attachment, while the PTO drives the snow-moving components. A chute that still turns therefore does not prove that the blower is receiving PTO power.manuals.deere+1