ohn Deere 44-Inch Select Series Snowblower Care & Parts

john deere

John Deere 44-Inch Select Series Snowblower Maintenance, Parts and Repair Guide

The John Deere 44-inch Select Series snowblower is a front-mounted, two-stage attachment driven by the tractor’s power take-off (PTO) through a belt. It has no engine or fuel system of its own. This guide covers gearbox oil checks, wear inspection, parts identification, and diagnosis when the auger stops, the belt wears prematurely, or the blower clears unevenly. Deere published more than one Select Series manual, so match the attachment and tractor before applying a service procedure or ordering a part.manuals.deere+4

44-Inch Select Series Snowblower Maintenance

Before inspecting, adjusting, or unclogging the blower, stop on level ground, disengage the PTO, lower the attachment to the ground, set the parking brake, shut off the engine, and remove the key. Wait for all movement to stop before leaving the seat. Use a clean-out tool, never your hands, to clear a blockage. Do not rely on the tractor lift to support the blower while you work beneath it. If a documented belt procedure calls for raising the attachment, support it as directed and keep clear of the spring-loaded belt tensioner.manuals.deere+2

Maintenance Schedule and Service Points

The preinstallation gearbox check below is a Deere instruction for the configuration covered by operator’s manual OMM175856. The other rows give inspection or service triggers, not fixed maintenance intervals.manuals.deere+3

Maintenance task Interval or trigger Specification or inspection point Owner action
Check both gearbox oil levels Before installing the attachment, as directed in OMM175856 Auger gearbox and snowblower drive gearbox; check with the attachment removed and the drive gearbox approximately level Identify the two plugs using the manual illustration. Check each level separately and top up only as directed. manuals.deere+1
Inspect the drive belt, guides, and idlers When drive becomes erratic or the belt wears rapidly or breaks Look for belt damage, rubbing at a guide, or a visibly misaligned idler. An idler is a pulley that redirects or tensions the belt. Confirm the belt route, guide positions, and tension procedure before adjusting or installing a new belt. manuals.deere+2
Inspect the shear hardware and rotating parts After striking an object, or if the auger or impeller stops Check for a broken shear bolt and for visible damage to the auger, impeller, or housing Replace confirmed broken shear hardware with the exact specified part. Stop if a rotating part is bent or contacts the housing. manuals.deere+1
Inspect the scraper blade and skid shoes When clearing becomes uneven, or during a preseason condition check Look for a bent or uneven scraper edge and compare the wear and settings of both shoes Replace damaged wear parts as needed; reset both shoes using the procedure for the attachment and clearing surface. manuals.deere+1

Lubrication and Fluid Requirements

The configuration covered by OMM175856 has two separate oil check points: one for the auger gearbox and one for the snowblower drive gearbox. Deere directs owners to perform the check with the attachment off the tractor and the drive gearbox approximately level. Both gearboxes have removable plugs for checking and adding oil, but the manual identifies neither gearbox as having serviceable internal components. An oil check is not an instruction to split the housing or rebuild the unit.manuals.deere+1

Use the service section of the manual matched to your attachment to confirm the lubricant grade, level reference, and plug locations before adding oil. If the gearbox has been replaced and its identity is uncertain, ask a Deere dealer to confirm the specification for the installed assembly. Fresh oil around a plug, housing seam, or shaft is a reason to locate the leak rather than keep topping up.manuals.deere+1

Wear Checks That Can Reveal Repair Needs

  • Scraper blade and skid shoes: The scraper is the lower edge across the housing; the shoes set its clearance from the surface. Compare the shoes side to side before blaming the scraper for a strip of snow left on one side. If the shoes are even, look for a bent scraper or damage to its mounting edge.manuals.deere+1

  • Belt, guides, and idlers: A frayed belt edge or a shiny rubbing mark gives you a place to inspect. Note which edge is damaged and where it runs nearest a guide. Deere specifically directs owners to check guide adjustment and idler alignment when belts wear too fast or break.manuals.deere+1

  • Auger, impeller, and guards: After an impact, look from outside the openings for bent auger flights, a distorted impeller blade, fresh scrape marks inside the housing, or damaged guards. These are visual checks, not proof of a failed bearing or gearbox. Do not test-run the blower if a rotating part may contact the housing or a guard cannot be secured.manuals.deere+1

Preseason Preparation and Storage

Before fitting the blower, check the gearbox levels if required by your manual, inspect the scraper and shoes, and verify that the mounting and lift hardware match the tractor. Check that the chute turns and the deflector moves through their normal travel with the tractor shut down. When removing the blower for storage, follow the attachment-removal sequence in the applicable manual, clear accumulated snow and debris, and let the attachment dry before putting it away. Follow the tractor’s own instructions for fuel and battery storage.manuals.deere+2

Once you find a worn part, identify the assembly it belongs to before ordering. A belt that drives the blower, a bracket that mounts it, and a spring that assists the lift can all be listed under different diagrams.manuals.deere+2

Finding the Correct 44-Inch Select Series Snowblower Replacement Parts

Model, Serial Number, and Configuration Checks

Record the blower’s full product identification number (PIN), the tractor model and PIN, and any identification on the installed mounting or lift kit. If the attachment label is hard to find, use the illustration in the operator’s manual under “Record Identification Numbers.” If a used blower came without readable identification, photograph the gearbox, belt routing, front hitch, and lift hardware for the dealer; tractor fit alone is not enough to identify a used attachment.manuals.deere+3

Dealer listings distinguish the 700DM package for earlier X300 Series tractors and certain X500 Series tractors from 7007M and 700FM packages listed for 2016-and-later applications. These are package identifiers, not universal serial breaks or proof that their service parts interchange. The X350R is also an example of why tractor-side hardware matters: the 700FM dealer listing specifies a supplemental lift-assist kit for that tractor. Apply any serial limits shown in the catalog to the specific part you are ordering.greenpartstore+3

Parts Diagrams and Manuals

John Deere’s Select Series operator’s manuals include OMM170956, OMM175574, and OMM175856. The title page of OMM175856 identifies the X350, X350R, X354, X370, X380, X584, and X590; use the manual that matches your installed configuration rather than choosing by the 44-inch width alone. The 44-inch attachment for 100 Series tractors has separate documentation.manuals.deere+4

In the John Deere Parts Catalog, select the attachment listing that matches the PIN, open the relevant illustrated assembly, and use the diagram callout to find the corresponding orderable part number. A callout is the item’s position in the illustration, not the number you order. If the catalog shows a replacement number for an older part, confirm that it applies to your serial range and whether it supplies a single component or a complete assembly.greenpartstore+3

Replacement Parts and Fitment Checks

The numbered examples below are listed by GreenPartStore for the 44-inch blower used with the X350. They are useful starting points for that application, not blanket fitment for every Select Series attachment.greenpartstore

Component Part number, where verified Fitment qualification What to check before ordering
Scraper blade M155105 Listed for the 44-inch blower on the X350 Match the lower housing diagram and check whether mounting hardware is listed separately. greenpartstore
Drive belt M174506 Listed for the 44-inch blower on the X350 Match the attachment PIN and belt diagram. Do not order it as an X350 mower-deck belt or assume it fits every 44-inch blower. manuals.deere+2
Chute spout control cable AM134404 Listed for the 44-inch blower on the X350 Confirm the failed control changes deflector angle. A problem turning the whole chute points to the separate directional control. manuals.deere+1
Skid shoe Identify in the attachment housing diagram Match the shoe and mounting hardware to the housing Compare both shoes and check the mounting slots and fasteners for damage before ordering. manuals.deere+1
Gearbox Identify by assembly and attachment PIN The drive gearbox and auger gearbox are separate assemblies Confirm which gearbox leaks or has failed and what comes with the replacement assembly. manuals.deere+1

Shear Bolts and Other Critical Hardware

A shear bolt is designed to break under overload to protect the parts it drives. If an auger section or the impeller stops, use the applicable manual’s shear-bolt illustration and parts diagram to identify the hardware at that location. Do not assume auger and impeller hardware is interchangeable, or order a generic kit based only on clearing width. Use the Deere-specified bolt and matching hardware; a standard bolt or a stronger substitute can defeat the protection. If the specified bolt fails again, stop and inspect for an obstruction, damaged rotating parts, or binding rather than fitting a stronger fastener.manuals.deere+1

Parts Sources in the USA and Canada

  • USA: Start with the John Deere Parts Catalog, then give a U.S. authorized John Deere dealer the attachment PIN, tractor PIN, and diagram item. GreenPartStore also provides separate X300 and X350 snowblower listings that help distinguish configurations.greenpartstore+2

  • Canada: Use the same John Deere Parts Catalog to identify the assembly, then have a Canadian authorized John Deere dealer confirm fitment and any replacement part number. If comparing a U.S. listing with a Canadian quote, check the currency and total delivered cost rather than comparing the displayed prices alone.greenpartstore

44-Inch Select Series Snowblower Problems and Repairs

Deere’s Select Series troubleshooting chart ties specific symptoms to checks, including shear bolts and belts for lost rotation, guides and idlers for short belt life, and skid shoes and lift assist for uneven clearing. Those checks narrow the fault; they do not establish which part failed on your machine. Use the shutdown procedure above before inspecting anything.manuals.deere

Troubleshooting at a Glance

Symptom Plausible causes First safe check Repair direction or escalation
An auger section or the impeller does not turn Broken shear bolt; worn or broken drive belt Look for impact damage and check the shear hardware at the affected location Replace only confirmed failed hardware. If both stages stopped and the belt is intact, have the drive path checked before ordering a gearbox. manuals.deere+1
Belt frays or breaks prematurely Misadjusted guides or misaligned idler Note the damaged edge and look for matching rub marks along the belt path Correct the routing, guide setting, or alignment before fitting another belt. manuals.deere+1
Blower leaves more snow on one side Uneven skid shoes or incorrect 44-inch lift-assist adjustment; visible scraper damage may also affect clearing With the housing lowered on a flat surface, compare both shoes and sight along the scraper Set the shoes evenly. Repair confirmed scraper damage; investigate lift setup if the housing still sits unevenly. manuals.deere+1
Lift lever does not lock in the raised position Lift-system yoke out of adjustment on the documented 44-inch setup Lower the blower and check for damaged or missing linkage hardware Use the applicable lift-height adjustment procedure. Do not transport it raised if the latch will not hold. manuals.deere+1

An Auger Section or the Impeller Does Not Turn

What stopped matters. If you noticed that one side stopped feeding snow while the blower still discharged from the other side, start with the shear hardware for the affected auger section. If neither the auger nor the impeller appeared to run, inspect the belt path as well. Deere lists both damaged belts and broken shear bolts under this symptom; neither observation alone proves gearbox failure.manuals.deere

After shutdown, look for packed material or impact damage without reaching into the housing. If the shear bolt alone has failed, clear the obstruction with a tool and replace the hardware using the applicable procedure. If the belt is intact, the shear hardware is sound, and drive still does not reach the blower, have the PTO-to-attachment drive path checked. Stop if the impeller rubs the housing, an auger flight is bent, or a shaft appears displaced.manuals.deere+2

The Drive Belt Frays or Breaks Prematurely

A replacement belt that quickly wears on the same edge is a reason to inspect the belt path before buying another. Deere’s chart calls out guide adjustment and idler alignment. With the attachment isolated, compare the installed route with the manual illustration and look for a guide with a corresponding rub mark, an idler that sits visibly out of line, or a loose or bent bracket.manuals.deere+1

If inspection confirms incorrect routing or a guide out of position, correct it using the procedure for your configuration and replace the damaged belt. The documented replacement procedure uses a spring-loaded tensioning arm; do not improvise a way to hold it back. Seek service if an idler mount is bent, the correct alignment cannot be established, or the replacement belt still tracks against a guide.manuals.deere+2

The Snowblower Clears Unevenly

A consistent strip of snow on one side points first to the way the housing is sitting. Deere directs owners to check for uneven skid shoes and, on the 44-inch unit, the lift-assist spring adjustment. With the blower lowered on a flat surface, compare shoe positions and wear. Check whether the scraper is straight and whether the housing itself sits level.manuals.deere+1

If the shoes are sound but set unevenly, adjust them using the manual’s procedure for the clearing surface. If a shoe is distorted or the scraper is bent, replace the damaged wear part before trying to compensate with lift adjustment. If the housing still sits crooked with sound, evenly adjusted shoes, have the lift setup and mounting points checked, particularly after an impact.manuals.deere+1

The Lift Lever Will Not Lock in the Raised Position

For the 44-inch setup covered by OMM175856, Deere identifies lift-system yoke adjustment as a check when the lever will not lock. With the blower on the ground, check the accessible linkage for a missing retainer, an obviously bent part, or an installation that does not match the lift assembly illustration. If the hardware is sound, use the manual’s lift-height and yoke adjustment procedure rather than increasing spring tension to force the latch to engage.manuals.deere+1

If the latch still will not hold, or if the linkage is bent or the spring hardware is damaged, leave the attachment lowered and arrange service. Keep clear of the loaded spring and do not work beneath the attachment while diagnosing the latch.manuals.deere+1

Owner Maintenance or Professional Repair?

Gearbox level checks, skid-shoe adjustments, scraper replacement, and replacement of correctly identified shear hardware are reasonable owner jobs when the matching manual supplies the procedure and you can isolate the attachment safely. Belt replacement is also documented, but it requires correct routing, safe support where specified, and control of the spring-loaded tensioner.manuals.deere+3

Use a dealer or qualified repair shop for a bent impeller, damaged housing or lift mounts, unresolved belt alignment, a PTO fault, or a gearbox leak that needs more than an identified plug correction. Before authorizing a gearbox replacement after an impact, ask the shop to confirm which assembly failed and whether the shafts, rotating parts, and housing are still serviceable. Compare the confirmed repair scope, parts availability, and local labor quote with the condition and value of the complete attachment.manuals.deere+2

Frequently Asked Questions

Does OMM175856 apply to every 44-inch Select Series snowblower?

No. Its title names specific Select Series tractor models, and Deere published other Select Series manuals. Match the attachment PIN and tractor configuration with Deere or an authorized dealer before using its installation or adjustment instructions.manuals.deere+2

Can I order parts from a 47-inch diagram if both blowers are in the same manual?

Not on that basis alone. The manual covers both widths but identifies some procedures and hardware as 44-inch only. Use the 44-inch attachment diagram and treat a part as shared only when the catalog confirms the same orderable number for both applications.manuals.deere+2

Why do I need to identify both the attachment and the tractor?

The attachment identification helps match parts such as the scraper, belt, and gearboxes. The tractor identification helps match installation hardware, including lift-assist components. This matters particularly when a used blower is sold without the kit that originally connected it to the tractor.manuals.deere+2