Kubota M59 Tractor Maintenance, Parts and Repair Guide
The Kubota M59 is a diesel tractor-loader-backhoe, not a snowblower. This guide covers tractor maintenance, replacement-parts identification, and repair checks for its hydrostatic transmission, cooling system, loader and backhoe. The associated factory equipment includes the TL1350 front loader and BT1200 backhoe; any snowblower fitted to the tractor requires its own model-specific instructions and parts catalog.arepairmanual
Kubota M59 Maintenance
Before servicing, park on firm, level ground, apply the parking brake and lower the attachments to the ground. Stop the engine and remove the key. Kubota’s workshop instructions also require disconnecting the battery negative cable and placing a “Do Not Operate” tag at the operator’s station before service or repair. Allow hot components to cool, relieve hydraulic pressure before disconnecting lines, and never work beneath equipment supported only by a jack or hydraulic pressure.arepairmanual
Maintenance Schedule and Service Points
The following table separates model-specific dealer service guidance from condition-based inspections. Use the applicable operator’s manual for the complete schedule, including initial services, adjustment procedures and attachment lubrication points.
| Maintenance task | Verified interval or trigger | Specification or inspection point | Owner action |
|---|---|---|---|
| Engine oil and filter | Coleman Equipment lists an initial change at 50 hours, then every 200 hours | Correct diesel-engine oil and engine oil filter | Record the service date and hour-meter reading; the dealer also recommends annual oil servicing |
| Tractor grease fittings | Dealer guidance: at least every 50 hours | Use the tractor lubrication diagram to locate the applicable fittings | Clean fittings before applying grease |
| TL1350 loader fittings | Dealer guidance: at least every 10 hours | Loader pivot and cylinder-pin lubrication points | Follow the loader lubrication diagram rather than the tractor’s longer interval |
| Hydraulic and HST high-pressure filters | Dealer guidance: initially at 50 hours, then every 200 hours | These are separate filter applications | Identify both filters before buying service parts |
| Electrical wiring | Kubota workshop guidance: annually | Loose connections, damaged insulation, missing grommets and insecure clamps | Repair damaged wiring and restore its protection and routing |
| Hydraulic hoses and cylinders | Condition-based inspection when leaks or damage appear | Abrasion, exposed reinforcement, wet fittings and damaged rods | Stop using an affected circuit when damage could cause hose failure or uncontrolled movement |
| Loader and backhoe joints | Condition-based inspection during lubrication or after impact | Cracked pins, missing retainers, displaced bushings and damaged mounting points | Identify the damaged assembly before ordering parts |
The oil, filter and lubrication intervals above are M59-specific dealer guidance. The annual wiring inspection and service-isolation precautions appear in Kubota’s workshop documentation. Condition-based inspections are not substitutes for the full maintenance schedule.arepairmanual+1
Lubrication and Fluid Requirements
Engine oil
Kubota’s M59 workshop manual lists an engine crankcase capacity, including the filter, of 9.4 liters or 9.9 US quarts. Treat this as an approximate service quantity: complete the refill using the manual’s level-checking procedure rather than pouring in the entire listed amount without checking.arepairmanual
Oil selection requires more than choosing a viscosity. The workshop documentation includes M59-specific external-EGR oil qualifications, while current dealer service listings offer 15W-40 engine oil for this model. Confirm the current approved oil classification and temperature-appropriate viscosity against the engine identification and applicable manual before purchasing oil. Do not select oil solely because its container says “diesel.”arepairmanual+1
Transmission and hydraulic fluid
The transmission lubricant also serves as hydraulic fluid. Kubota’s original M59 workshop documentation specifies Kubota UDT or Super UDT and lists an approximate transmission-case capacity of 46 liters, or 12.2 US gallons. It also cautions against mixing different brands.arepairmanual
Coleman Equipment’s M59 service listing includes Super UDT2. When changing from an existing fluid or servicing a machine with an unknown maintenance history, have a Kubota dealer confirm the appropriate current product and refill procedure. Do not substitute ordinary hydraulic oil based only on viscosity.colemanequip
Front axle oil and grease
The front axle has its own lubricant supply. Kubota lists UDT or Super UDT fluid, or the specified SAE 80 or SAE 90 gear oil, for this application. The approximate listed capacity is 12.5 liters, or 13.2 US quarts. This is separate from the transmission refill.arepairmanual
The tractor lubrication table specifies multipurpose grease, including NLGI No. 2, for its listed grease points. Follow the individual lubrication instructions: some points call for grease until it emerges, while others require only a moderate amount. Do not assume the same quantity or interval applies to the tractor, loader and backhoe.arepairmanual
Wear Checks That Can Reveal Repair Needs
Use lubrication stops to inspect the surrounding joint, not simply to add grease.
An M59 owner reported finding a broken lower loader-bucket pin while greasing the machine. That report does not establish a widespread defect, but it illustrates why visible pin ends, retainers and adjacent mounting ears deserve attention during maintenance.tractorbynet
Useful condition-based checks include:
-
Inspect exposed loader and backhoe pins for cracks, displacement or missing retainers.
-
Look for movement between a pin and its mounting ear, rather than assuming all looseness comes from a replaceable bushing.
-
Examine hydraulic hoses where they bend, rub against brackets or pass close to moving joints.
-
Inspect cylinder rods for scoring, corrosion and oil accumulation.
-
Check accessible wiring for chafing, stretched sections and broken connector locks.
-
Look for debris between the cooling-system components, not just on the visible front screen.
These are inspection directions, not diagnoses. A loose joint may require a pin, bushings or structural repair; a wet cylinder may require seal work, rod repair or further investigation. Confirm the damaged component before ordering. Kubota’s workshop documentation emphasizes correct component identification, clean measurement and specified repair procedures.arepairmanual
Preseason Preparation and Storage
Before returning a stored tractor to work, review its service record and check for fluid loss, damaged wiring, deteriorated hoses and debris around the cooling components. Do not use a brief successful start as proof that the hydraulic system and attachments are ready for loaded operation.
For extended storage, use the applicable operator’s manual for the fuel, battery and corrosion-protection procedure. Kubota’s workshop precautions require battery charging in a ventilated area away from flames and sparks; disconnect the negative cable first and reconnect it last. Never run the engine in an enclosed storage building.arepairmanual
Finding wear is only the first step. Replacement parts must match the tractor, engine or attachment assembly—and, where applicable, its production version.
Finding the Correct Kubota M59 Replacement Parts
Model, Serial Number and Configuration Checks
Record the following before contacting a parts department:
-
Tractor model and complete serial number.
-
Engine model and serial number.
-
Loader model and serial number.
-
Backhoe model and identification details.
-
Relevant option or accessory identification.
-
Photographs of the assembly and any readable markings.
Kubota’s workshop manual distinguishes the tractor identification plate, tractor serial number, engine serial number and loader serial number. Use its identification illustrations to locate them; do not assume one number identifies the complete tractor-loader-backhoe package. The documented engine model is V2403-M-TE3-TLB1, but verify the engine actually installed, particularly on a machine with an uncertain repair history.arepairmanual
Production differences matter. The M59 dealer catalog contains separate “old type” and “new type” main hydraulic-pump diagrams, along with ordering notes for replacement components. It also lists different wheel configurations. These distinctions do not provide a universal serial-number cutoff, so have the dealer resolve the applicable version before ordering a pump, associated piping or wheel-related parts.colemanequip
Engine parts require similar care. Kubota specifically warns that replacement components for the E3 engine must match that engine’s emissions specification rather than being selected from another emissions-level engine merely because the basic model looks similar.arepairmanual
Parts Diagrams and Manuals
Three types of documentation serve different purposes:
-
The operator’s manual covers operation, routine maintenance, fluid checks and owner adjustments.
-
The illustrated parts catalog identifies assemblies, components, quantities and ordering qualifications.
-
The workshop manual supplies diagnostic procedures, measurements, repair limits and disassembly instructions.
Kubota’s workshop manual identifies the M59 tractor, TL1350 loader and BT1200 backhoe together. Coleman Equipment lists M59 parts manual 97898-23990 and shop manual 9Y121-01120. Confirm the applicable edition and coverage before ordering, especially when looking for attachment-specific information.arepairmanual+1
In an illustrated catalog, a diagram reference number is not the orderable part number. For example, the M59 HST servo-regulator diagram uses reference 020 for proportional valve TD170-59310. The same catalog shows several HST assembly numbers under one diagram reference, demonstrating why the reference number alone is insufficient.colemanequip
A superseded number is an older ordering number replaced by a current one. Ask the parts department to confirm both the current number and whether the replacement requires additional components. Multiple numbers on a page do not, by themselves, prove unrestricted interchangeability.
Replacement Parts and Fitment Checks
The following numbers appear in Coleman Equipment’s M59 catalog. They provide a useful starting point, not a substitute for checking the machine’s identification and the current catalog qualifications.colemanequip
| Component | Verified part number | Fitment qualification | What to check before ordering |
|---|---|---|---|
| Engine oil filter | HH164-32430 | Listed for the M59 | Confirm the installed engine and current replacement number |
| Outer air-filter element | 59800-26110 | Listed as the outer element | Distinguish it from the inner element; inspect the housing and seals |
| Inner air-filter element | 3A111-19130 | Listed as the inner element | Do not order the outer element in its place |
| Fuel filter | 15521-43160 | Listed for the M59 fuel system | Match the filter assembly and inspect its associated seals |
| HST high-pressure filter | HHTA0-59900 | Separate from the hydraulic oil filter | Confirm which filter position is being serviced |
| Hydraulic oil filter | HHTA0-37710 | Separate hydraulic-filter application | Do not confuse it with the HST high-pressure filter |
| HST proportional valve | TD170-59310 | Listed in the HST servo-regulator assembly | Require a confirmed diagnosis and check the applicable assembly before purchase |
Pins, Retainers and Other Critical Hardware
Loader pivot pins, backhoe pins and attachment retainers are not snowblower shear bolts. Select them from the applicable loader, backhoe or bucket diagram rather than by appearance alone.
If a pin is damaged, inspect the mating bushings, mounting ears and retaining arrangement before deciding the repair scope. Do not substitute an ordinary bolt or weld a damaged pin as an improvised repair. Kubota’s workshop precautions advise against makeshift tools, parts and procedures.arepairmanual
Parts Sources in the USA and Canada
In the USA, Kubota’s online parts catalog includes an M59 listing. Coleman Equipment also provides M59 diagrams, service parts and manual listings. Use the assembly diagram to identify the component, then request a serial-number and supersession check before ordering.colemanequip+1
In Canada, Kubota Canada’s Parts Catalogue allows owners to view component details and ordering numbers. A local Kubota Canada dealer can help resolve configuration questions and place the order. Halifax Kubota also provides an online parts-finder route and parts-department assistance.kubota+1
For a cross-border quotation, confirm the currency and delivered cost separately. A catalog listing does not establish current stock, delivery timing or export availability.
Kubota M59 Problems and Repairs
Model-specific owner discussions describe slow backhoe swing, restricted hydraulic-cooler airflow and uneven forward or reverse travel. These are reported symptoms, not proof of a universal defect. Use them to guide inspection, while reserving component replacement for faults confirmed through the applicable diagnostic procedure.tractorbynet
Troubleshooting at a Glance
| Symptom | Plausible causes supported by the evidence | First safe check | Repair direction or escalation |
|---|---|---|---|
| Backhoe swings unusually slowly | Hydraulic selector configuration or a fault within the dedicated swing circuit | With the machine isolated, identify selector positions and inspect accessible hoses | Correct a verified configuration issue; obtain swing-circuit testing if the fault remains |
| Forward or reverse travel jerks or behaves inconsistently | HST control, sensor, valve or hydraulic-service issue requiring diagnosis | Inspect accessible pedal-area obstructions, wiring and service history | Stop using an unpredictably moving tractor; request HST diagnostic testing |
| Hydraulic system becomes excessively hot | Restricted airflow through the hydraulic heat exchanger; other causes remain possible | Inspect the cooler and spaces between cooling components with the engine stopped and cool | Clean confirmed external obstruction; investigate persistent heating |
| Loader bucket develops abnormal looseness or a displaced pin | Damaged pin, retainer, bushing or mounting structure | Lower and unload the attachment; inspect visible pin ends and retainers | Repair the confirmed joint damage before further loaded operation |
The first three symptoms appear in M59 owner discussions. The loader-pin concern is supported by an individual owner’s reported inspection finding; none establishes a failure rate.tractorbynet+1
Backhoe Swing Is Slow but Other Functions Still Work
The useful distinction is whether only swing is affected or whether the entire backhoe is weak. Kubota’s M59 documentation identifies a separate swing-pump circuit, so normal digging-cylinder operation does not automatically clear the swing system.colemanequip+1
An M59 owner reported improved swing operation after attending to the selectors used when changing between backhoe and three-point-hitch operation. Treat selector position as a configuration check, not a guaranteed repair. Identify the controls and their correct positions in the applicable manual before moving them; do not force an unfamiliar selector.tractorbynet
With the machine shut down, attachments grounded and hydraulic pressure relieved:
-
Check the prescribed selector configuration.
-
Inspect accessible swing hoses for damage or obvious restriction.
-
Note whether the symptom began after attachment changes or hydraulic servicing.
-
Record whether both swing directions are affected.
If correcting a confirmed configuration error restores operation, further component replacement may be unnecessary. If swing remains weak, have the dedicated circuit tested. Do not replace the main pump solely because one backhoe function is slow.
Forward or Reverse Travel Jerks or Does Not Respond Consistently
An M59 owner described uneven travel that remained after several attempted repairs, with a directional HST control valve eventually reported as the solution. That experience identifies one possible diagnostic path—not a reason to replace the same valve on every tractor with a travel complaint.tractorbynet
The dealer catalog confirms that proportional valve TD170-59310 belongs to the HST servo-regulator assembly. It does not establish that the valve is faulty on a particular machine.colemanequip
Safe initial checks include inspecting the pedal area for obstruction, checking accessible connectors for damage and confirming which hydraulic filters were installed during the last service. Separate observations carefully:
-
Does the problem affect forward, reverse or both?
-
Does it occur cold, hot or at all temperatures?
-
Did it begin after servicing or wiring work?
-
Are warning indications present?
If travel is unpredictable, stop operating the tractor. Sensor checks, electrical measurements and hydraulic testing should follow the workshop procedure. Do not bypass safety switches or adjust regulator screws experimentally.
Hydraulic Oil Becomes Excessively Hot
An M59 owner reported dirt accumulating on the hydraulic heat exchanger ahead of the radiator and protective screen. This makes cooler obstruction a worthwhile inspection point, but overheating alone does not prove an airflow problem.tractorbynet
With the engine stopped and the cooling components safe to approach, inspect the visible screen, cooler faces and the spaces between them. A clean screen does not establish that the cooler behind it is clear.
If inspection confirms debris buildup, clean it using the method permitted by the applicable manual, taking care not to damage the fins. Refit removed guards and covers before operation.
If heating continues, stop repeated loaded testing. Fluid condition, hydraulic restrictions and internal losses require further diagnosis. Never loosen a hydraulic connection to judge pressure or remove a hot radiator cap. Kubota’s service precautions specifically warn about pressurized fluid and hot coolant.arepairmanual
Loader Bucket Looseness or a Damaged Pivot Pin
Visible pin displacement, missing retainers or sudden changes in bucket movement require inspection before further loading. One owner’s broken-pin report shows that damage can be discovered during lubrication rather than after complete loss of function.tractorbynet
Lower the bucket fully, remove its load and isolate the tractor. Inspect only accessible areas without entering pinch points or relying on the hydraulic system to hold the linkage.
If a retainer is missing, establish whether the pin has moved and damaged the surrounding parts. If a pin is cracked or broken, inspect the bushings and mounting ears before ordering replacements. A new pin will not correct an elongated or cracked mounting hole.
Pin removal and joint repair may require supporting heavy components and controlling linkage movement. Seek service when the support arrangement, structural condition or required measurements are uncertain.
Owner Maintenance or Professional Repair?
Documented oil and filter changes, accessible lubrication, visual wiring checks and external inspections may suit an owner with the correct manual, tools and means of safely handling fluids and components. Kubota’s workshop manual provides separate procedures and specifications for more involved service work.arepairmanual
Professional repair is appropriate when the work involves:
-
Unpredictable HST travel.
-
Hydraulic pressure or flow testing.
-
Persistent overheating after external blockage is removed.
-
Internal pump, valve or transmission repairs.
-
Heavy loader or backhoe components requiring controlled support.
-
Cracked mounting ears, damaged frames or uncertain pin-bore condition.
-
Electrical faults that require testing beyond the owner’s equipment or knowledge.
Before approving a major repair, request the confirmed fault, test results, required parts and any associated damage. For an HST assembly or hydraulic-pump replacement, the catalog’s multiple assembly numbers and old/new-type distinctions make correct identification especially important.colemanequip
A repair-versus-replacement decision should use the actual repair scope, structural condition, parts quotation and local labor estimate—not the symptom alone.
Frequently Asked Questions
Is the M59 a snowblower model?
No. It is a tractor-loader-backhoe. The associated factory equipment includes the TL1350 loader and BT1200 backhoe. A separately fitted snowblower must be identified by its own manufacturer, model and serial number before selecting shear hardware, driveline parts or gearbox lubricant.arepairmanual
Are the hydraulic filter and HST filter the same?
No. The M59 dealer listing identifies hydraulic oil filter HHTA0-37710 separately from HST high-pressure filter HHTA0-59900. Confirm the filter position and current catalog application before ordering.colemanequip
Can a hydraulic pump be ordered using only “Kubota M59”?
That is insufficient for a reliable order. The catalog distinguishes old-type and new-type main-pump assemblies and includes additional ordering qualifications. Supply the tractor serial number and have the dealer check the installed configuration.colemanequip
Does jerky travel mean the complete hydrostatic transmission has failed?
Not necessarily. M59 owner reports include control-related faults, and the parts catalog identifies separately serviceable regulator components. The correct next step is diagnosis, not automatic replacement of the complete HST assembly.